logo

An Investigation into Grease Behavior in Thermal EHL

If you want to confirm some technical details before you order,
just need to send a message or e-mail: [email protected].
Then our professional sales staff will contact you within 2 hours.

B.-Y. Yang's research works | Henan University of Science .

B.-Y. Yang's 6 research works with 39 citations and 68 reads, including: Determination of lubricant elastic shear modulus under conditions of high pressure and high shear rates

Molybdenum disulfide - Wikiped

Molybdenum disulfide (or moly) is an inorganic compound composed of molybdenum and sulfur. Its chemical formula is MoS 2. The compound is classified as a transition metal dichalcogenide. It is a silvery black solid that occurs as the mineral molybdenite, the principal ore for molybdenum.[6] MoS 2 is relatively unreactive. It is unaffected by ...

Fatty-acids-and-antioxidant-effects-on-grease .

Critical physiochemical properties are therefore dependent on the consistency of grease and their behavior in ... pp. 1–6. 291 Mansot, J.L., 1989. Structural investigation of ...

Heat Transfer and Thermal Elastic Deformation Analysis on the Piston/Cylinder Interface of Axial Piston Machin

In this paper, the authors present in detail the computational approach implemented to study the heat transfer and thermal elastic deformation phenomena. Simulation results for the piston/cylinder interface of an existing hydrostatic unit are discussed, considering different operating conditions and focusing on the influence of the thermal aspect.

Current Projects | Research groups | Imperial College Lond

In addition to improving the EHL modelling tools, the project will attempt to generate charts that indicate the contact conditions where the simplified EHL solutions may be used with sufficient accuracy and those where the full CFD solution may be needed. Investigation will also be made into suitable rheology models for grease as a lubricant.

Lubricants | Free Full-Text | Grease Aging Effects on Film .

Several film thickness measurements were performed with three fresh and aged lubricating greases, their base and bled oils under a wide range of operating conditions using a ball-on-disc test rig with optical interferometry. The analysis of the film thickness measurements is in agreement with the observations of several authors and adds some important aspects regarding separate film properties ...

A Theoretical and Experimental Study of EHL Lubricated .

It is known that the apparent viscosity of grease varies with service time and that grease starvation is important in EHL. However, these effects were often ignored in the research of EHL lubricated with grease. This paper deals with the thixotropy of grease and determines which value of rheological parameters can be used in numerical analysis.

Lubricants - mdpi.c

The contact between teeth requires investigation into their tribological behavior focusing on the enamel wear process against natural teeth and/or artificial teeth, allowing us to obtain useful information on the tribological behavior of restorative materials.

Tribology Transactions: Vol 49, No

An Investigation into Grease Behavior in Thermal EHL Circular Contacts. YANSHUANG WANG & BOYUAN YANG . ... Analytical and Experimental Investigation of Laser-Textured Mechanical Seal Faces Etsion et al. Volume 42, 1999 - Issue 3. Published online: 25 Mar 2008 ...

prof. Ing. Martin Hartl, Ph.D. - Publications – B

An Investigation on Adhesion Behavior of Solid Particles in Water Contaminated Wheel-Rail Contact. In 2018 International Symposium on Rail Infrastructure Systems Engineering (i-RISE 2018). Proceedings.

The Elastohydrodynamic Traction of a Grease LGLT2 .

The elastohydrodynamic (EHD) traction coefficients of a lubricating grease LGLT2 were tested at various loads and rolling speeds on a self-made test rig. Traction coefficient versus slide-to-roll ratio curves were generated. Formulae which relate traction coefficient with normal load and rolling speed are put forth.

Cornelis H. Venner – Research Output — University of .

Investigation into the viscoelastic behavior of a thin lubricant layer in an EHL contact van Emden, E., Venner, ... Effect of Thickener Particle Geometry and Concentration on the Grease EHL Film Thickness at Medium Speeds Cyriac, F., Lugt, ... Thermal Elastohydrodynamic Lubrication of an Optimized Cam–Tappet Pair in Smooth Contact ...

Thermal Elastohydrodynamic Lubrication of Ceramic .

ABSTRACTThe effect of thermal conductivity on point elastohydrodynamic lubrication (EHL) contacts was discussed with representative engineering ceramics and steel by a non-Newtonian thermal EHL analysis. Through this investigation, fundamentals of EHL characteristics of contact surfaces composed of different thermal conductivities were generally revealed and a combination of optimum ceramic ...

Engineering Fluid Dynamics Group: Refereed Articles - TF

Investigation into the viscoelastic behavior of a thin lubricant layer in an EHL contact. Trib. Int. 111 pp. 197-210 (2017). N.P. Kruyt and O. Millet An analytical theory for the capillary bridge force between spheres J. Fluid Mech. 812 pp. 129-151 (2017). 2016. N.P. Kruyt and L. Rothenburg A micromechanical study of dilatancy of granular materials

Viscosity Loss in PFPE Lubricant for Space Applications .

So far, a number of studies of rolling bearing life have been developed with respect to elastohydrodynamic lubrication, especially in relation to film parameter4,5,6). An investigation was carried out to clarify merits or demerits of lithium soap grease and paraffinic mineral base oil concerning bearing life7).

Aircraft landing gear greased slider bearing steady-state .

Read "Aircraft landing gear greased slider bearing steady-state thermo-elastohydrodynamic concept model, Tribology International" on DeepDyve, the largest online rental service for scholarly research with thousands of academic publications available at your fingertips.

Mechanical degradation of lubricating grease in an EHL .

Mechanical degradation of grease in an EHL line contact between two steel rollers is studied. Three successive lubricating phases involving “fully grease covered rollers,” “slippage and grease separation,” and “formation of liquid lubricant reservoirs” are observed and characterized.